Rochester, NY · Motor Control Centers
Rochester, NY: Motor Control Centers Purchase and Removal
We purchase motor control centers throughout Rochester and the surrounding New York market — units still energized and scheduled for replacement, equipment already sitting dead after an upgrade, and lots coming out of a full plant closure. We buy the gear and we do the removal: one company, one offer, one certificate of insurance.
Same-day written offer
Get a Written Offer
Send the asset list, or just describe what is in the room. We come back the same business day with a written, itemized offer.
Faster: call 954-740-1983
Email an asset list to electricalequipmentbuyers@gmail.com
Mon–Sat, 7am–7pm ET. We never resell your contact information.
- Location
- Rochester, NY
- Equipment
- Motor Control Centers
- Ratings
- MCC line-ups, buckets, VFD section
- Offer
- Same business day
- Removal
- Our crews
- Phone
- 954-740-1983
Equipment
Motor Control Centers we buy in Rochester
Coverage in Rochester is run off our New York routing along I-87, I-90, I-95, I-84 and the Thruway. Coordination with Con Edison, National Grid, NYSEG, Central Hudson, PSEG Long Island on clearances, metering removal and final disconnect is part of the scope, not a change order. New York is two completely different jobs sharing a state line. In the five boroughs and the lower Hudson Valley the work is vertical and permit-heavy: switchboards and busway risers coming out of pre-war commercial buildings, hospital and university plants replacing essential-power systems, and Con Edison network gear on a renewal cycle that never really stops. Freight elevators, night windows and street-level staging decide the schedule far more than the rigging does. Upstate is horizontal and industrial — the Buffalo and Niagara Falls electrochemical and metals legacy, Rochester optics and imaging plants that have been shedding infrastructure for two decades, Syracuse and Utica manufacturing, and the semiconductor and battery build-out that is now retiring the gear it replaced. Bus duct is unusually common in both halves, because so much of this building stock was wired when busway was the standard answer.
If the Rochester equipment is still carrying load, we phase it. Usually that means dead sections and spares first, then distribution as circuits are released, then the main line-up once the last feeder is isolated. The phasing goes into the offer so nobody is improvising in an energized room at two in the morning.
| Item | Detail |
|---|---|
| Ratings | MCC line-ups, buckets, VFD sections |
| Scope | Low and medium voltage MCCs |
| Nameplates | Allen-Bradley CENTERLINE, Square D Model 6, Eaton Freedom & Advantage, GE 8000 & Evolution, Siemens, Westinghouse, Toshiba, ABB |
| Condition | Working, retired, water-damaged or already dismantled |
| Minimum | One section, one unit, or a whole plant lot |
Valuation
What it is worth
Transformer oil is the item sellers in Rochester worry about most, and fairly so. We test it, drain it, manifest it through licensed handlers and hand you the documentation. PCB-suspect units are handled under their own waste profile. The cost of that handling is already inside the offer, so nothing surprises you after the fact.
New York note
New York is two completely different jobs sharing a state line. In the five boroughs and the lower Hudson Valley the work is vertical and permit-heavy: switchboards and busway risers coming out of pre-war commercial buildings, hospital and university plants replacing essential-power systems, and Con Edison network gear on a renewal cycle that never really stops. Freight elevators, night windows and street-level staging decide the schedule far more than the rigging does. Upstate is horizontal and industrial — the Buffalo and Niagara Falls electrochemical and metals legacy, Rochester optics and imaging plants that have been shedding infrastructure for two decades, Syracuse and Utica manufacturing, and the semiconductor and battery build-out that is now retiring the gear it replaced. Bus duct is unusually common in both halves, because so much of this building stock was wired when busway was the standard answer.
Related
Related pages
Not in Rochester? These are close:
Common questions
Questions
Do we have to disconnect the equipment before you arrive?
No. We handle removal. Your electrician or the utility performs the final isolation and we verify it; from there our crews lock out, cut and cap cable at the gland, unbolt the sections, skate them out and load them. If the Rochester room is still partly live we phase the work.
How do you handle transformer oil in Rochester?
Oil is tested, drained and manifested through licensed handlers, and you receive the documentation with your paperwork. PCB-suspect units go under a separate waste profile. Nothing is left on your pad in Rochester and nothing gets dumped — the handling cost is already in the offer.
When do we get paid?
Before the equipment leaves your Rochester dock. Wire, company check or cashier's check, whichever your accounting group prefers. On large phased projects we pay per load as it ships rather than holding everything until the end.
What if the equipment is old or has no test records?
We still quote it. Records raise the number — a NETA test report on a breaker or a transformer is the single document that most improves what we can pay — but their absence disqualifies nothing. We price Rochester equipment on what our technicians and the replacement market say it is worth.
Motor Control Centers in Rochester?
One written offer covering purchase, removal and freight.