New York, NY · Circuit Breakers
New York, NY: Circuit Breakers Purchase and Removal
If you have circuit breakers to sell in New York, the fastest route to a real number is a nameplate photo and a count. We price against the replacement market for this equipment class, subtract our own removal cost openly, and send a written itemized offer the same business day.
Same-day written offer
Get a Written Offer
Send the asset list, or just describe what is in the room. We come back the same business day with a written, itemized offer.
Faster: call 954-740-1983
Email an asset list to electricalequipmentbuyers@gmail.com
Mon–Sat, 7am–7pm ET. We never resell your contact information.
- Location
- New York, NY
- Equipment
- Circuit Breakers
- Ratings
- 15 A – 6,000 A frames
- Offer
- Same business day
- Removal
- Our crews
- Phone
- 954-740-1983
Equipment
Circuit Breakers we buy in New York
Coverage in New York is run off our New York routing along I-87, I-90, I-95, I-84 and the Thruway. Coordination with Con Edison, National Grid, NYSEG, Central Hudson, PSEG Long Island on clearances, metering removal and final disconnect is part of the scope, not a change order. New York is two completely different jobs sharing a state line. In the five boroughs and the lower Hudson Valley the work is vertical and permit-heavy: switchboards and busway risers coming out of pre-war commercial buildings, hospital and university plants replacing essential-power systems, and Con Edison network gear on a renewal cycle that never really stops. Freight elevators, night windows and street-level staging decide the schedule far more than the rigging does. Upstate is horizontal and industrial — the Buffalo and Niagara Falls electrochemical and metals legacy, Rochester optics and imaging plants that have been shedding infrastructure for two decades, Syracuse and Utica manufacturing, and the semiconductor and battery build-out that is now retiring the gear it replaced. Bus duct is unusually common in both halves, because so much of this building stock was wired when busway was the standard answer.
If the New York equipment is still carrying load, we phase it. Usually that means dead sections and spares first, then distribution as circuits are released, then the main line-up once the last feeder is isolated. The phasing goes into the offer so nobody is improvising in an energized room at two in the morning.
| Item | Detail |
|---|---|
| Ratings | 15 A – 6,000 A frames |
| Scope | Molded case, insulated case, air, vacuum |
| Nameplates | Square D, Eaton, Cutler-Hammer, General Electric, Siemens, ABB, Westinghouse, ITE, Federal Pacific, Allis-Chalmers |
| Condition | Working, retired, water-damaged or already dismantled |
| Minimum | One section, one unit, or a whole plant lot |
Valuation
What it is worth
Transformer oil is the item sellers in New York worry about most, and fairly so. We test it, drain it, manifest it through licensed handlers and hand you the documentation. PCB-suspect units are handled under their own waste profile. The cost of that handling is already inside the offer, so nothing surprises you after the fact.
New York note
New York is two completely different jobs sharing a state line. In the five boroughs and the lower Hudson Valley the work is vertical and permit-heavy: switchboards and busway risers coming out of pre-war commercial buildings, hospital and university plants replacing essential-power systems, and Con Edison network gear on a renewal cycle that never really stops. Freight elevators, night windows and street-level staging decide the schedule far more than the rigging does. Upstate is horizontal and industrial — the Buffalo and Niagara Falls electrochemical and metals legacy, Rochester optics and imaging plants that have been shedding infrastructure for two decades, Syracuse and Utica manufacturing, and the semiconductor and battery build-out that is now retiring the gear it replaced. Bus duct is unusually common in both halves, because so much of this building stock was wired when busway was the standard answer.
Related
Related pages
Not in New York? These are close:
Common questions
Questions
What is the smallest job you will take in New York?
A single transformer, one switchgear section, a pallet of breakers or a few boxes of breakers is worth a call. Because we route crews across New York continuously, small New York pickups usually get added to an existing run rather than priced as a dedicated trip.
How fast can you get to a New York site?
Written offers go out the same business day in nearly every case. After acceptance, typical mobilization to New York is a few business days for a straightforward removal and one to two weeks for a full plant scope that needs phasing, rigging plans or utility coordination.
Do we have to disconnect the equipment before you arrive?
No. We handle removal. Your electrician or the utility performs the final isolation and we verify it; from there our crews lock out, cut and cap cable at the gland, unbolt the sections, skate them out and load them. If the New York room is still partly live we phase the work.
How do you handle transformer oil in New York?
Oil is tested, drained and manifested through licensed handlers, and you receive the documentation with your paperwork. PCB-suspect units go under a separate waste profile. Nothing is left on your pad in New York and nothing gets dumped — the handling cost is already in the offer.
Circuit Breakers in New York?
One written offer covering purchase, removal and freight.