Yonkers, NY · Electrical Bus Plug Buyers
Electrical Bus Plug Buyers in Yonkers, NY
Retired bus plugs in Yonkers is usually worth more than assumed. A large share of what gets sent to a yard as scrap actually resells into service, and the difference between those two numbers is frequently significant. We will tell you honestly which category yours falls into before you commit to anything.
Same-day written offer
Get a Written Offer
Send the asset list, or just describe what is in the room. We come back the same business day with a written, itemized offer.
Faster: call 954-740-1983
Email an asset list to electricalequipmentbuyers@gmail.com
Mon–Sat, 7am–7pm ET. We never resell your contact information.
- Location
- Yonkers, NY
- Desk
- Electrical Bus Plug Buyers
- Ratings
- 30 A – 1,200 A fusible and breaker plu
- Offer
- Same business day
- Payment
- Before load-out
- Phone
- 954-740-1983
This city
Bus Plugs buyers serving Yonkers
Yonkers sits in New York, where Con Edison, National Grid, NYSEG, Central Hudson, PSEG Long Island feed the load and I-87, I-90, I-95, I-84 and the Thruway carry the freight. Sites near those corridors cost us less to service, and that shows up in your offer rather than in our margin. New York City, Buffalo, Rochester, Syracuse and Albany are routine stops and Yonkers work routes with them.
Documentation travels with the job: a certificate of insurance naming your entity, a W-9, a signed purchase agreement itemizing each asset and its price, oil or PCB manifests where applicable, and weight tickets or a bill of lading for what leaves the Yonkers site.
| Item | Detail |
|---|---|
| Ratings | 30 A – 1,200 A fusible and breaker plugs |
| Scope | All busway systems, all vintages |
| Nameplates | Square D I-Line, General Electric Spectra and Armor-Clad, Siemens, Eaton and Cutler-Hammer Pow-R-Way, Westinghouse, Federal Pacific, ITE, Bulldog |
| Condition | Working, retired, water-damaged or already dismantled |
| Minimum | One section, one unit, or a whole plant lot |
Equipment
What we take out of Yonkers sites
Fusible switch plugs
Square D I-Line, GE Spectra and Armor-Clad, Eaton Pow-R-Way, Siemens, Westinghouse, ITE and Bulldog fusible plugs from 30 A to 800 A. Clean stabs, an intact interlock and a working handle mechanism are what separate a reusable plug from a copper recovery item.
Circuit-breaker and starter plugs
Breaker plugs, combination motor starter plugs, ground-fault plugs, transformer plugs and cable tap boxes. Combination starter plugs in particular are hard to source new and hold value well even at older vintages.
New York specifics
New York is two completely different jobs sharing a state line. In the five boroughs and the lower Hudson Valley the work is vertical and permit-heavy: switchboards and busway risers coming out of pre-war commercial buildings, hospital and university plants replacing essential-power systems, and Con Edison network gear on a renewal cycle that never really stops. Freight elevators, night windows and street-level staging decide the schedule far more than the rigging does. Upstate is horizontal and industrial — the Buffalo and Niagara Falls electrochemical and metals legacy, Rochester optics and imaging plants that have been shedding infrastructure for two decades, Syracuse and Utica manufacturing, and the semiconductor and battery build-out that is now retiring the gear it replaced. Bus duct is unusually common in both halves, because so much of this building stock was wired when busway was the standard answer.
Nearby
Nearby and related
Nearby New York coverage — crews serving Yonkers also run to:
Common questions
Yonkers questions
How fast can you get to a Yonkers site?
Written offers go out the same business day in nearly every case. After acceptance, typical mobilization to Yonkers is a few business days for a straightforward removal and one to two weeks for a full plant scope that needs phasing, rigging plans or utility coordination.
Do we have to disconnect the equipment before you arrive?
No. We handle removal. Your electrician or the utility performs the final isolation and we verify it; from there our crews lock out, cut and cap cable at the gland, unbolt the sections, skate them out and load them. If the Yonkers room is still partly live we phase the work.
How do you handle transformer oil in Yonkers?
Oil is tested, drained and manifested through licensed handlers, and you receive the documentation with your paperwork. PCB-suspect units go under a separate waste profile. Nothing is left on your pad in Yonkers and nothing gets dumped — the handling cost is already in the offer.
When do we get paid?
Before the equipment leaves your Yonkers dock. Wire, company check or cashier's check, whichever your accounting group prefers. On large phased projects we pay per load as it ships rather than holding everything until the end.
What if the equipment is old or has no test records?
We still quote it. Records raise the number — a NETA test report on a breaker or a transformer is the single document that most improves what we can pay — but their absence disqualifies nothing. We price Yonkers equipment on what our technicians and the replacement market say it is worth.
Bus Plugs in Yonkers?
One call, one written offer, one crew. Payment before the trailer leaves.