Yonkers, NY · Electrical Switchgear
Yonkers, NY: Electrical Switchgear Purchase and Removal
If you have switchgear to sell in Yonkers, the fastest route to a real number is a nameplate photo and a count. We price against the replacement market for this equipment class, subtract our own removal cost openly, and send a written itemized offer the same business day.
Same-day written offer
Get a Written Offer
Send the asset list, or just describe what is in the room. We come back the same business day with a written, itemized offer.
Faster: call 954-740-1983
Email an asset list to electricalequipmentbuyers@gmail.com
Mon–Sat, 7am–7pm ET. We never resell your contact information.
- Location
- Yonkers, NY
- Equipment
- Electrical Switchgear
- Ratings
- 480 V – 38 kV, up to 5,000 A
- Offer
- Same business day
- Removal
- Our crews
- Phone
- 954-740-1983
Equipment
Electrical Switchgear we buy in Yonkers
New York is two completely different jobs sharing a state line. In the five boroughs and the lower Hudson Valley the work is vertical and permit-heavy: switchboards and busway risers coming out of pre-war commercial buildings, hospital and university plants replacing essential-power systems, and Con Edison network gear on a renewal cycle that never really stops. Freight elevators, night windows and street-level staging decide the schedule far more than the rigging does. Upstate is horizontal and industrial — the Buffalo and Niagara Falls electrochemical and metals legacy, Rochester optics and imaging plants that have been shedding infrastructure for two decades, Syracuse and Utica manufacturing, and the semiconductor and battery build-out that is now retiring the gear it replaced. Bus duct is unusually common in both halves, because so much of this building stock was wired when busway was the standard answer. For Yonkers specifically, that density helps: crews already move through New York City, Buffalo, Rochester, Syracuse and Albany, so mobilization is a scheduling question rather than a cost problem.
If the Yonkers equipment is still carrying load, we phase it. Usually that means dead sections and spares first, then distribution as circuits are released, then the main line-up once the last feeder is isolated. The phasing goes into the offer so nobody is improvising in an energized room at two in the morning.
| Item | Detail |
|---|---|
| Ratings | 480 V – 38 kV, up to 5,000 A |
| Scope | Low and medium voltage, indoor and outdoor |
| Nameplates | Square D, Schneider, Eaton, Cutler-Hammer, General Electric, Siemens, ABB, Allis-Chalmers, Westinghouse, Federal Pacific, Powell, Zenith, Russelectric |
| Condition | Working, retired, water-damaged or already dismantled |
| Minimum | One section, one unit, or a whole plant lot |
Valuation
What it is worth
Copper is the floor under most of this equipment, and it is a floor that moves. Bus bar, windings and feeder cable set a minimum value we can always pay on a Yonkers lot; resale demand for the specific make and model is what lifts the offer above it. Obsolete breakers and discontinued panelboard interiors are the clearest example — unglamorous parts that plants cannot buy new anywhere.
New York note
New York is two completely different jobs sharing a state line. In the five boroughs and the lower Hudson Valley the work is vertical and permit-heavy: switchboards and busway risers coming out of pre-war commercial buildings, hospital and university plants replacing essential-power systems, and Con Edison network gear on a renewal cycle that never really stops. Freight elevators, night windows and street-level staging decide the schedule far more than the rigging does. Upstate is horizontal and industrial — the Buffalo and Niagara Falls electrochemical and metals legacy, Rochester optics and imaging plants that have been shedding infrastructure for two decades, Syracuse and Utica manufacturing, and the semiconductor and battery build-out that is now retiring the gear it replaced. Bus duct is unusually common in both halves, because so much of this building stock was wired when busway was the standard answer.
Related
Related pages
Not in Yonkers? These are close:
Common questions
Questions
Do you buy equipment that is still energized and in service?
Yes, and most of what we buy is. We quote it now and remove it on your cutover date. Telling us at the quote stage which Yonkers assets are still live lets us build the phasing and the clearance coordination into the schedule from the beginning.
Our electrical room is in a basement with a tight door. Is that a problem?
It is routine. Switchgear sections, transformers and gensets frequently have to be cut down or partially disassembled to clear a door width, an elevator limit or a stair turn. The access survey at your Yonkers site establishes the path before we commit to a date, and that cost is already inside the offer.
Will you take the equipment we cannot sell along with the good items?
Yes, and this is usually why sellers choose us. Cherry-picking leaves you holding the leftovers of the leftovers. We price the Yonkers lot as a whole — good gear, obsolete gear and the scrap fraction together — so the electrical room ends up genuinely empty.
Do you provide documentation for surplus property or audit records?
Yes. Itemized purchase agreements, weight tickets, bills of lading, oil disposal manifests and recycling documentation are standard on Yonkers purchases. Public agencies and audited facilities get the paperwork their process requires without having to ask twice.
Electrical Switchgear in Yonkers?
One written offer covering purchase, removal and freight.