Yonkers, NY · Electrical Wire And Cable Buyers
We Buy Wire and Cable in Yonkers, NY
Retired wire and cable in Yonkers is usually worth more than assumed. A large share of what gets sent to a yard as scrap actually resells into service, and the difference between those two numbers is frequently significant. We will tell you honestly which category yours falls into before you commit to anything.
Same-day written offer
Get a Written Offer
Send the asset list, or just describe what is in the room. We come back the same business day with a written, itemized offer.
Faster: call 954-740-1983
Email an asset list to electricalequipmentbuyers@gmail.com
Mon–Sat, 7am–7pm ET. We never resell your contact information.
- Location
- Yonkers, NY
- Desk
- Electrical Wire and Cable Buyers
- Ratings
- #12 AWG – 1,000 MCM, copper and alumin
- Offer
- Same business day
- Payment
- Before load-out
- Phone
- 954-740-1983
This city
Wire and Cable buyers serving Yonkers
Yonkers sits in New York, where Con Edison, National Grid, NYSEG, Central Hudson, PSEG Long Island feed the load and I-87, I-90, I-95, I-84 and the Thruway carry the freight. Sites near those corridors cost us less to service, and that shows up in your offer rather than in our margin. New York City, Buffalo, Rochester, Syracuse and Albany are routine stops and Yonkers work routes with them.
The sequence is short. You send nameplate photos, a one-line diagram or just a list. We return a written itemized offer the same business day with a proposed removal window. On acceptance we survey access in Yonkers — door widths, floor loading, dock, elevator, crane needs — then mobilize, lock out, disconnect, rig, load and sweep. Payment before the truck leaves.
| Item | Detail |
|---|---|
| Ratings | #12 AWG – 1,000 MCM, copper and aluminum |
| Scope | Feeder, MV shielded, tray, control, reels |
| Nameplates | Southwire, General Cable, Okonite, Kerite, Prysmian, Encore Wire, Cerro, Houston Wire and Cable, Belden |
| Condition | Working, retired, water-damaged or already dismantled |
| Minimum | One section, one unit, or a whole plant lot |
Equipment
What we take out of Yonkers sites
Feeder and building wire
THHN, XHHW and RHW copper and aluminum feeders from #12 AWG through 1,000 MCM, single conductors and multi-conductor assemblies, in conduit or free-air. Recovered building wire is the highest-volume item in most plant electrical lots.
Medium-voltage and shielded cable
5 kV, 15 kV, 25 kV and 35 kV shielded power cable, EPR and XLPE insulated, tape and wire shielded, single conductor and triplexed. Long unspliced runs and full reels can resell as cable rather than as recovered copper, which is worth considerably more.
New York specifics
New York is two completely different jobs sharing a state line. In the five boroughs and the lower Hudson Valley the work is vertical and permit-heavy: switchboards and busway risers coming out of pre-war commercial buildings, hospital and university plants replacing essential-power systems, and Con Edison network gear on a renewal cycle that never really stops. Freight elevators, night windows and street-level staging decide the schedule far more than the rigging does. Upstate is horizontal and industrial — the Buffalo and Niagara Falls electrochemical and metals legacy, Rochester optics and imaging plants that have been shedding infrastructure for two decades, Syracuse and Utica manufacturing, and the semiconductor and battery build-out that is now retiring the gear it replaced. Bus duct is unusually common in both halves, because so much of this building stock was wired when busway was the standard answer.
Nearby
Nearby and related
We cover New York statewide, so if the equipment is not in Yonkers itself, one of these is probably closer:
Common questions
Yonkers questions
What is the smallest job you will take in Yonkers?
A single transformer, one switchgear section, a pallet of breakers or a few boxes of breakers is worth a call. Because we route crews across New York continuously, small Yonkers pickups usually get added to an existing run rather than priced as a dedicated trip.
How fast can you get to a Yonkers site?
Written offers go out the same business day in nearly every case. After acceptance, typical mobilization to Yonkers is a few business days for a straightforward removal and one to two weeks for a full plant scope that needs phasing, rigging plans or utility coordination.
Do we have to disconnect the equipment before you arrive?
No. We handle removal. Your electrician or the utility performs the final isolation and we verify it; from there our crews lock out, cut and cap cable at the gland, unbolt the sections, skate them out and load them. If the Yonkers room is still partly live we phase the work.
How do you handle transformer oil in Yonkers?
Oil is tested, drained and manifested through licensed handlers, and you receive the documentation with your paperwork. PCB-suspect units go under a separate waste profile. Nothing is left on your pad in Yonkers and nothing gets dumped — the handling cost is already in the offer.
When do we get paid?
Before the equipment leaves your Yonkers dock. Wire, company check or cashier's check, whichever your accounting group prefers. On large phased projects we pay per load as it ships rather than holding everything until the end.
Wire and Cable in Yonkers?
One call, one written offer, one crew. Payment before the trailer leaves.